In this example, we only plan to create one partition which will be partition 1. The next step is to create a new partition on the disk, a task which is performed by entering “n” (for new partition) and “p” (for primary partition) Command (m for help): n I/O size (minimum/optimal): 512 bytes / 512 bytesĪs we can see from the above, the fdisk output of the disk currently has no partitions because it is a previously unused disk. Sector size (logical/physical): 512 bytes / 512 bytes In order to view the current partitions on the disk enter the p command:ĭisk /dev/sdb: 34.4 GB, 34359738368 bytesĢ55 heads, 63 sectors/track, 4177 cylinders Strongly recommended to switch off the mode (command 'c') and change display units toĪs instructed, switch off DOS compatible mode and change the units to sectors by entering the c and u commands: WARNING: DOS-compatible mode is deprecated. Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) The Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel Building a new DOS disklabel with disk identifier 0xd1082b01.Ĭhanges will remain in memory only, until you decide to write them.Īfter that, of course, the previous content won't be recoverable. This is achieved using the fdisk utility which takes as a command-line argument on the device to be partitioned. The next step is to create one or more Linux partitions on the new disk drive. Currently, the drive has no partitions shown (because we have yet to create any).Īt this point, we have a choice of creating partitions and file systems on the new drive and mounting them for access or adding the disk as a physical volume as part of a volume group. # ls /dev/sd*Īs shown above, the new hard drive has been assigned to the device file /dev/sdb. The following would be the output for the same system if we attach second hard disk drive. This shows that the disk drive is represented by /dev/sda itself divided into 2 partitions, represented by /dev/sda1 and /dev/sda2. The following is the output from a system with only one physical disk drive – # ls /dev/sd* For example, the first device might be /dev/sda, the second /dev/sdb and so on. Typically, the disk drives in a system are assigned to a device name beginning with hd or sd followed by a letter to indicate the device number. Finding the New Hard Drive in RHEL 6.xĪssuming the drive as visible to the BIOS, it should automatically be detected by the operating system. This article assumes that the new physical hard drive has been installed on the system and is visible to the operating system. Create a Linux file system on those partitions and then mount the disk at a specific mount point so that they can be accessed. One very simplest method is to create a Linux partition on the new disk. Configuring RHEL 6 to Automatically Mount a Filesystem.Creating a Filesystem on an RHEL 6 Disk Partition.x to add more space by installing the disk. We shall look at the steps necessary to configure on Red Hat Enterprise Linux 6. Fortunately, disk space is now one of the cheapest. This is one of the most common problems encountered by system administrators these days since the servers are tending to run out of disk space to store excess data. So assuming the machine doesn't list the drive, try attaching it using USB or Firewire if either of those options are available.This article helps you to configure and add a new disk to the Linux box. Firewire possibly less but should still be supported by most. I'm pretty certain USB is supported by anything on the planet. This might be because of the connector between the machine and the drive. If you only get to see as many drives as your system has internally, your external HD apparently wasn't detected. When you external HD was detected the letter is probably the one furthest down the alfabet, assuming you're shown a list. Something starting with /dev/sd followed by a letter and possibly a number. What might happen is that when you say install, it asks you to either prepare or specify the drive on which to install, specified as something like /dev/sda or /dev/sda1 or something like that. I'm guessing you're hoping to find a destination drive explicitly labeled as the external drive.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |